Dr. H. Li is a full professor in materials processing and advanced manufacturing at the Northwestern Polytechnical University, Xi’an, China. In the past two decades, his researches are more focused on plasticity related solid mechanics, multi-scale and multi-physics modelling and simulation of deformation-based manufacturing and precision forming of hard-to-deform materials with complex and complicated structures. He has an extensive research experience in these materials processing and manufacturing areas and secured 10 major research funds from governmental funding agencies and industries for conducting research and technology development. In 2015, he was awarded the prestigious National Science Fund for Excellent Young Scholars and enrolled in the National Youth Top-notch Talent Program in China and published over 120 peer reviewed research articles with a significant impact in materials processing and manufacturing arena. Dr. Mingwang Fu is a leading expert in the area of materials processing and manufacturing engineering and has been conducting research on deformation-based materials processing, especially for forming-based micromanufacturing. He has established a world-class research group at The Hong Kong Polytechnic University with the main focuses on advanced materials processing, numerical modeling and simulation, size effect–based micromechanics, and damage and fracture in deformation-based manufacturing and product service. He is a chair professor of advanced manufacturing, the fellow of Society of Manufacturing Engineers (SME), and Hong Kong Institute of Engineers (HKIE). He is also the Royal Society Wolfson Visiting Fellow and serving a number of international journals, including Int. J. Plast., Int. J. Mach. Tools Manuf., Int. J. Mech. Sci., Mater. Des., Int. J. Damage Mech., Int. J. Adv. Manuf. Technol, Adv. Manuf., J. Manuf. Mater. Process., and Manuf. Rev., as an editorial board member or associate editor.

• 1. Introduction to Deformation-Based Manufacturing2. Deformation Inhomogeneity3. Damage Evolution and Ductile Fracture4. Deformation-Induced Compressive Instability5. Deformation-Induced Springback Defects6. Inhomogeneous Deformation-Induced Surface Roughening Defects7. Inhomogeneous deformation-Induced Flow Defects8. Microstructure Abnormality-Related Defects

Dr. H. Li is a full professor in materials processing and advanced manufacturing at the Northwestern Polytechnical University, Xi’an, China. In the past two decades, his researches are more focused on plasticity related solid mechanics, multi-scale and multi-physics modelling and simulation of deformation-based manufacturing and precision forming of hard-to-deform materials with complex and complicated structures. He has an extensive research experience in these materials processing and manufacturing areas and secured 10 major research funds from governmental funding agencies and industries for conducting research and technology development. In 2015, he was awarded the prestigious National Science Fund for Excellent Young Scholars and enrolled in the National Youth Top-notch Talent Program in China and published over 120 peer reviewed research articles with a significant impact in materials processing and manufacturing arena. Dr. Mingwang Fu is a leading expert in the area of materials processing and manufacturing engineering and has been conducting research on deformation-based materials processing, especially for forming-based micromanufacturing. He has established a world-class research group at The Hong Kong Polytechnic University with the main focuses on advanced materials processing, numerical modeling and simulation, size effect–based micromechanics, and damage and fracture in deformation-based manufacturing and product service. He is a chair professor of advanced manufacturing, the fellow of Society of Manufacturing Engineers (SME), and Hong Kong Institute of Engineers (HKIE). He is also the Royal Society Wolfson Visiting Fellow and serving a number of international journals, including Int. J. Plast., Int. J. Mach. Tools Manuf., Int. J. Mech. Sci., Mater. Des., Int. J. Damage Mech., Int. J. Adv. Manuf. Technol, Adv. Manuf., J. Manuf. Mater. Process., and Manuf. Rev., as an editorial board member or associate editor.

• 1. Introduction to Deformation-Based Manufacturing2. Deformation Inhomogeneity3. Damage Evolution and Ductile Fracture4. Deformation-Induced Compressive Instability5. Deformation-Induced Springback Defects6. Inhomogeneous Deformation-Induced Surface Roughening Defects7. Inhomogeneous deformation-Induced Flow Defects8. Microstructure Abnormality-Related Defects

Dr. H. Li is a full professor in materials processing and advanced manufacturing at the Northwestern Polytechnical University, Xi’an, China. In the past two decades, his researches are more focused on plasticity related solid mechanics, multi-scale and multi-physics modelling and simulation of deformation-based manufacturing and precision forming of hard-to-deform materials with complex and complicated structures. He has an extensive research experience in these materials processing and manufacturing areas and secured 10 major research funds from governmental funding agencies and industries for conducting research and technology development. In 2015, he was awarded the prestigious National Science Fund for Excellent Young Scholars and enrolled in the National Youth Top-notch Talent Program in China and published over 120 peer reviewed research articles with a significant impact in materials processing and manufacturing arena. Dr. Mingwang Fu is a leading expert in the area of materials processing and manufacturing engineering and has been conducting research on deformation-based materials processing, especially for forming-based micromanufacturing. He has established a world-class research group at The Hong Kong Polytechnic University with the main focuses on advanced materials processing, numerical modeling and simulation, size effect–based micromechanics, and damage and fracture in deformation-based manufacturing and product service. He is a chair professor of advanced manufacturing, the fellow of Society of Manufacturing Engineers (SME), and Hong Kong Institute of Engineers (HKIE). He is also the Royal Society Wolfson Visiting Fellow and serving a number of international journals, including Int. J. Plast., Int. J. Mach. Tools Manuf., Int. J. Mech. Sci., Mater. Des., Int. J. Damage Mech., Int. J. Adv. Manuf. Technol, Adv. Manuf., J. Manuf. Mater. Process., and Manuf. Rev., as an editorial board member or associate editor.

• 1. Introduction to Deformation-Based Manufacturing2. Deformation Inhomogeneity3. Damage Evolution and Ductile Fracture4. Deformation-Induced Compressive Instability5. Deformation-Induced Springback Defects6. Inhomogeneous Deformation-Induced Surface Roughening Defects7. Inhomogeneous deformation-Induced Flow Defects8. Microstructure Abnormality-Related Defects