Tadashi Tanuma is a Professor at Teikyo University, Japan. He is the head of the Laboratory of Fluid-Structural Simulation and Design in the Strategic Innovation and Research Center. He also works for the Graduate School of Science & Engineering and the Department of Mechanical and Precision System Engineering in Teikyo University.Professor Tadashi Tanuma began his career as a development mechanical engineer in 1980 at Turbine Factory, Toshiba Corporation, Japan. He led the Turbomachinary Development Group from 1993. Subsequently, he joined the Steam Turbine Design Department in Keihin Product Operations of Toshiba Corporation. He developed and designed Toshiba 52-inch last stage long blade for nuclear power steam turbines and steel 40 and 48-inch last stage long blade for thermal power steam turbines as an aerodynamic engineer and led many research and development programs for steam and gas turbine efficiency enhancement technologies. He was the President of the Gas Turbine Society of Japan (2015).

• Part I Steam Turbine Cycles and Cycle Design Optimization1. Introduction to steam turbines for power plants2. Steam turbine cycles and cycle design optimization: the Rankine cycle, thermal power cycles, and IGCC power plants3. Steam turbine cycles and cycle design optimization: advanced ultra-supercritical thermal power plants and nuclear power plants4. Steam turbine cycles and cycle design optimization: combined cycle power plants5. Steam turbine life cycle cost evaluations and comparison with other power systemsPart II Steam Turbine Analysis, Measurement and Monitoring for Design Optimization6. Design and analysis for aerodynamic efficiency enhancement of steam turbines7. Steam turbine rotor design and rotor dynamics analysis8. Steam turbine design for load-following capability and highlyefficient partial operation9. Analysis and design of wet-steam stages10. Solid particle erosion analysis and protection design for steam turbines11. Steam turbine monitoring technology, validation, and verification tests for power plantsPart III Development of Materials, Blades and Important12. Development in materials for ultra-supercritical (USC) and advanced ultra-supercritical (A-USC) steam turbines13. Development of last-stage long blades for steam turbines14. Introduction of new sealing technologies for steam turbines15. Introduction of advanced technologies for steam turbine bearings16. Manufacturing technologies for key steam turbine partsPart IV Turbine Retrofitting and Advanced Applications in Power Generation17. Steam turbine retrofitting for the life extension of power plants18. Steam turbine retrofitting for power increase and efficiency enhancement19. Advanced geothermal steam turbines20. Steam turbines for solar thermal and other renewable energies21. Advanced ultra-supercritical pressure (A-USC) steam turbines and their combination with carbon capture and storage systems (CCS)22. Steam turbine roles and necessary technologies for stabilization of the electricity grid in the renewable energy era23. Conclusions

Tadashi Tanuma is a Professor at Teikyo University, Japan. He is the head of the Laboratory of Fluid-Structural Simulation and Design in the Strategic Innovation and Research Center. He also works for the Graduate School of Science & Engineering and the Department of Mechanical and Precision System Engineering in Teikyo University.Professor Tadashi Tanuma began his career as a development mechanical engineer in 1980 at Turbine Factory, Toshiba Corporation, Japan. He led the Turbomachinary Development Group from 1993. Subsequently, he joined the Steam Turbine Design Department in Keihin Product Operations of Toshiba Corporation. He developed and designed Toshiba 52-inch last stage long blade for nuclear power steam turbines and steel 40 and 48-inch last stage long blade for thermal power steam turbines as an aerodynamic engineer and led many research and development programs for steam and gas turbine efficiency enhancement technologies. He was the President of the Gas Turbine Society of Japan (2015).

• Part I Steam Turbine Cycles and Cycle Design Optimization1. Introduction to steam turbines for power plants2. Steam turbine cycles and cycle design optimization: the Rankine cycle, thermal power cycles, and IGCC power plants3. Steam turbine cycles and cycle design optimization: advanced ultra-supercritical thermal power plants and nuclear power plants4. Steam turbine cycles and cycle design optimization: combined cycle power plants5. Steam turbine life cycle cost evaluations and comparison with other power systemsPart II Steam Turbine Analysis, Measurement and Monitoring for Design Optimization6. Design and analysis for aerodynamic efficiency enhancement of steam turbines7. Steam turbine rotor design and rotor dynamics analysis8. Steam turbine design for load-following capability and highlyefficient partial operation9. Analysis and design of wet-steam stages10. Solid particle erosion analysis and protection design for steam turbines11. Steam turbine monitoring technology, validation, and verification tests for power plantsPart III Development of Materials, Blades and Important12. Development in materials for ultra-supercritical (USC) and advanced ultra-supercritical (A-USC) steam turbines13. Development of last-stage long blades for steam turbines14. Introduction of new sealing technologies for steam turbines15. Introduction of advanced technologies for steam turbine bearings16. Manufacturing technologies for key steam turbine partsPart IV Turbine Retrofitting and Advanced Applications in Power Generation17. Steam turbine retrofitting for the life extension of power plants18. Steam turbine retrofitting for power increase and efficiency enhancement19. Advanced geothermal steam turbines20. Steam turbines for solar thermal and other renewable energies21. Advanced ultra-supercritical pressure (A-USC) steam turbines and their combination with carbon capture and storage systems (CCS)22. Steam turbine roles and necessary technologies for stabilization of the electricity grid in the renewable energy era23. Conclusions