Dawid Taler – författare

This book presents new methods of numerical modelling of tube heat exchangers, which can be used to perform design and operation calculations of exchangers characterized by a complex flow system. It also proposes new heat transfer correlations for laminar, transition and turbulent flows. A large part of the book is devoted to experimental testing of heat exchangers, and methods for assessing the indirect measurement uncertainty are presented. Further, it describes a new method for parallel determination of the Nusselt number correlations on both sides of the tube walls based on the nonlinear least squares method and presents the application of computational fluid dynamic (CFD) modeling to determine the air-side Nusselt number correlations. Lastly, it develops a control system based on the mathematical model of the car radiator and compares this with the digital proportional-integral-derivative (PID) controller. The book is intended for students, academics and researchers, as well as for designers and manufacturers of heat exchangers.

This book presents new methods for solving inverse heat transfer problems occurring in thermal engineering. In the inverse problems analysed in the book, the temperature distribution inside a body or the parameters in the boundary conditions are determined based on temperature measurements at selected points of the body. Analytical and numerical methods for solving inverse heat conduction problems are presented, including the determination of transient thermal stresses in structural elements with simple and complex shapes. Methods for determining thermal stresses on the inner surface of pressure components based on measuring the temperature of the component inside the wall or based on measuring the temperature on an easily accessible, thermally insulated outer surface of the pressure component are presented. Methods for determining the optimum time temperature changes of the fluid in pressure components during heating or cooling are presented, so that the total circumferential stress resulting from pressure and thermal loading is equal to the permissible stress.A large part of the book is devoted to solving inverse problems in heat exchangers. The following inverse problems were solved: determination of the HTC distribution on the outer surface of a tube in the bundle of a crossflow heat exchanger, determination of the absorbed heat flux, fluid temperature and the HTC on the inner surface of the waterwall tube, simultaneous determination of heat transfer correlations for Nusselt numbers in heat exchangers on both tube wall surfaces, the control of water temperature at the outlet of the plate-fin and tube heat exchanger by changing the fan rotational speed and determination of the number of air fan revolutions based on the measurement of the water temperature at the outlet of the car radiator.The future time steps, regularisation of the inverse solution and pre-smoothing of measured temperature changes are used throughout the book to reduce the oscillation of the inverse solution over time. The book is intended for students, academics and researchers, as well as for designers and manufacturers working in the area of thermal engineering.

This book presents new methods for solving inverse heat transfer problems occurring in thermal engineering. In the inverse problems analysed in the book, the temperature distribution inside a body or the parameters in the boundary conditions are determined based on temperature measurements at selected points of the body. Analytical and numerical methods for solving inverse heat conduction problems are presented, including the determination of transient thermal stresses in structural elements with simple and complex shapes. Methods for determining thermal stresses on the inner surface of pressure components based on measuring the temperature of the component inside the wall or based on measuring the temperature on an easily accessible, thermally insulated outer surface of the pressure component are presented. Methods for determining the optimum time temperature changes of the fluid in pressure components during heating or cooling are presented, so that the total circumferential stress resulting from pressure and thermal loading is equal to the permissible stress.                A large part of the book is devoted to solving inverse problems in heat exchangers. The following inverse problems were solved: determination of the HTC distribution on the outer surface of a tube in the bundle of a crossflow heat exchanger, determination of the absorbed heat flux, fluid temperature and the HTC on the inner surface of the waterwall tube, simultaneous determination of heat transfer correlations for Nusselt numbers in heat exchangers on both tube wall surfaces, the control of water temperature at the outlet of the plate-fin and tube heat exchanger by changing the fan rotational speed and determination of the number of air fan revolutions based on the measurement of the water temperature at the outlet of the car radiator.                The future time steps, regularisation of the inverse solution and pre-smoothing of measured temperature changes are used throughout the book to reduce the oscillation of the inverse solution over time.                 The book is intended for students, academics and researchers, as well as for designers and manufacturers working in the area of thermal engineering.

This book presents new methods of numerical modelling of tube heat exchangers, which can be used to perform design and operation calculations of exchangers characterized by a complex flow system. It also proposes new heat transfer correlations for laminar, transition and turbulent flows. A large part of the book is devoted to experimental testing of heat exchangers, and methods for assessing the indirect measurement uncertainty are presented. Further, it describes a new method for parallel determination of the Nusselt number correlations on both sides of the tube walls based on the nonlinear least squares method and presents the application of computational fluid dynamic (CFD) modeling to determine the air-side Nusselt number correlations. Lastly, it develops a control system based on the mathematical model of the car radiator and compares this with the digital proportional-integral-derivative (PID) controller. The book is intended for students, academics and researchers, as well as for designers and manufacturers of heat exchangers.

This book presents new methods of numerical modelling of tube heat exchangers, which can be used to perform design and operation calculations of exchangers characterized by a complex flow system. It also proposes new heat transfer correlations for laminar, transition and turbulent flows. A large part of the book is devoted to experimental testing of heat exchangers, and methods for assessing the indirect measurement uncertainty are presented. Further, it describes a new method for parallel determination of the Nusselt number correlations on both sides of the tube walls based on the nonlinear least squares method and presents the application of computational fluid dynamic (CFD) modeling to determine the air-side Nusselt number correlations. Lastly, it develops a control system based on the mathematical model of the car radiator and compares this with the digital proportional-integral-derivative (PID) controller. The book is intended for students, academics and researchers, as well as for designers and manufacturers of heat exchangers.

This book comprises peer-reviewed papers presented at the 5th International Conference on Advanced Engineering Optimization Through Intelligent Techniques (AEOTIT) 2024. It combines contributions from academics and industry professionals, covering advanced optimization techniques across major engineering disciplines. The book discusses various optimization techniques and algorithms such as genetic algorithms, particle swarm optimization, differential evolution, whale optimization algorithm, artificial bee colony algorithm, arithmetic optimization algorithm, beat-worst-random and best-mean-random algorithms, teaching–learning-based optimization algorithm, gray wolf optimization, Jaya algorithm, Rao algorithms, and many other latest meta-heuristic techniques. It also explores several machine learning algorithms and their applications. Additionally, the book explores various multi-attribute decision-making methods such as AHP, TOPSIS, PROMETHEE, dominance-relations based method, Taguchi method, fuzzy logic, and their applications. This book serves as a valuable reference for students, researchers, and practitioners, helping them solve a wide range of optimization problems.