Christian Franck–University of Wisconsin-Madison, WI, USA;Karen Kasza–Columbia University, NY, USA;Jon Estrada, University of Michigan, MI, USA;Rosa De Finis–University of Salento, Italy;Geir Ólafsson–University of Bristol, UK;Suhasini Gururaja–Auburn University, AL, USA;Jevan Furmanski–University of Dayton Research Institute, OH, USA;Aaron Forster–National Institute of Standards and Technology, MD, USA;Pavan Kolluru–Texas A&M University, TX, USA;Mike Prime–Los Alamos National Laboratory, NM, USA;Tom Berfield–University of Louisville, KY, USA;Cahit Aydiner–Bogazici Universitesi, Turkey.

• Chapter 1. Development of PEEK matrix polymer composite and additive manufacturing by pellet extrusion method.- Chapter 2. Parkinsonian Hand Tremor Mitigation with Enhanced Wearable Device.- Chapter 3. Quantitative Measurement of Viscoelastic Properties of Soft Membranes Subjected to Finite Deformations based on Optical Coherence Elastography.- Chapter 4. Open Source Contour Method Analysis for Assessing Residual Stress in Weldments.- Chapter 5. Variation of initial bulk residual stresses in aluminum alloy 7050-T7451 and its effect on distortion of thin-walled structural parts.- Chapter 6. On the Use of iDIC (Integrated Digital Image Correlation) for the Slitting Method.- Chapter 7. A rapid procedure to re-construct S/N curve by using harmonic components of thermal signal.- Chapter 8. Rapid Fatigue Characterisation via Infrared Thermography of AM-CM Composites.- Chapter 9. Condition Assessment by Thermal Emission (CATE) for in situ monitoring of fatigue crack growth.- Chapter 10. Effect of geometrical discontinuities on mode shapes stress maps using infrared thermography.- Chapter 11. Induction thermography: influence of testing parameters for different crack geometry.- Chapter 12. Numerical Simulation of the Heat Dissipation During the Fatigue Test.- Chapter 13. A full experimental characterization of aged Nitrile Butadiene Rubbers (NBR).- Chapter 14. Characterization of the Effect of Cold Joints and Functional Grading in Stepwise Constructed Tensile Dog Bones with Embedded Digital Image Correlation.

Christian Franck–University of Wisconsin-Madison, WI, USA;Karen Kasza–Columbia University, NY, USA;Jon Estrada, University of Michigan, MI, USA;Rosa De Finis–University of Salento, Italy;Geir Ólafsson–University of Bristol, UK;Suhasini Gururaja–Auburn University, AL, USA;Jevan Furmanski–University of Dayton Research Institute, OH, USA;Aaron Forster–National Institute of Standards and Technology, MD, USA;Pavan Kolluru–Texas A&M University, TX, USA;Mike Prime–Los Alamos National Laboratory, NM, USA;Tom Berfield–University of Louisville, KY, USA;Cahit Aydiner–Bogazici Universitesi, Turkey.

• Chapter 1. Development of PEEK matrix polymer composite and additive manufacturing by pellet extrusion method.- Chapter 2. Parkinsonian Hand Tremor Mitigation with Enhanced Wearable Device.- Chapter 3. Quantitative Measurement of Viscoelastic Properties of Soft Membranes Subjected to Finite Deformations based on Optical Coherence Elastography.- Chapter 4. Open Source Contour Method Analysis for Assessing Residual Stress in Weldments.- Chapter 5. Variation of initial bulk residual stresses in aluminum alloy 7050-T7451 and its effect on distortion of thin-walled structural parts.- Chapter 6. On the Use of iDIC (Integrated Digital Image Correlation) for the Slitting Method.- Chapter 7. A rapid procedure to re-construct S/N curve by using harmonic components of thermal signal.- Chapter 8. Rapid Fatigue Characterisation via Infrared Thermography of AM-CM Composites.- Chapter 9. Condition Assessment by Thermal Emission (CATE) for in situ monitoring of fatigue crack growth.- Chapter 10. Effect of geometrical discontinuities on mode shapes stress maps using infrared thermography.- Chapter 11. Induction thermography: influence of testing parameters for different crack geometry.- Chapter 12. Numerical Simulation of the Heat Dissipation During the Fatigue Test.- Chapter 13. A full experimental characterization of aged Nitrile Butadiene Rubbers (NBR).- Chapter 14. Characterization of the Effect of Cold Joints and Functional Grading in Stepwise Constructed Tensile Dog Bones with Embedded Digital Image Correlation.

Christian Franck–University of Wisconsin-Madison, WI, USA;Karen Kasza–Columbia University, NY, USA;Jon Estrada, University of Michigan, MI, USA;Rosa De Finis–University of Salento, Italy;Geir Ólafsson–University of Bristol, UK;Suhasini Gururaja–Auburn University, AL, USA;Jevan Furmanski–University of Dayton Research Institute, OH, USA;Aaron Forster–National Institute of Standards and Technology, MD, USA;Pavan Kolluru–Texas A&M University, TX, USA;Mike Prime–Los Alamos National Laboratory, NM, USA;Tom Berfield–University of Louisville, KY, USA;Cahit Aydiner–Bogazici Universitesi, Turkey.

• Chapter 1. Development of PEEK matrix polymer composite and additive manufacturing by pellet extrusion method.- Chapter 2. Parkinsonian Hand Tremor Mitigation with Enhanced Wearable Device.- Chapter 3. Quantitative Measurement of Viscoelastic Properties of Soft Membranes Subjected to Finite Deformations based on Optical Coherence Elastography.- Chapter 4. Open Source Contour Method Analysis for Assessing Residual Stress in Weldments.- Chapter 5. Variation of initial bulk residual stresses in aluminum alloy 7050-T7451 and its effect on distortion of thin-walled structural parts.- Chapter 6. On the Use of iDIC (Integrated Digital Image Correlation) for the Slitting Method.- Chapter 7. A rapid procedure to re-construct S/N curve by using harmonic components of thermal signal.- Chapter 8. Rapid Fatigue Characterisation via Infrared Thermography of AM-CM Composites.- Chapter 9. Condition Assessment by Thermal Emission (CATE) for in situ monitoring of fatigue crack growth.- Chapter 10. Effect of geometrical discontinuities on mode shapes stress maps using infrared thermography.- Chapter 11. Induction thermography: influence of testing parameters for different crack geometry.- Chapter 12. Numerical Simulation of the Heat Dissipation During the Fatigue Test.- Chapter 13. A full experimental characterization of aged Nitrile Butadiene Rubbers (NBR).- Chapter 14. Characterization of the Effect of Cold Joints and Functional Grading in Stepwise Constructed Tensile Dog Bones with Embedded Digital Image Correlation.