R. Clift – författare

1,1 Applications of Slurry Transport Vast tonnages are pumped every year in the form of solid-liquid mixtures, known as slurries. The application which involves the largest quantities is the dredging industry, continually maintaining navigation in harbours and rivers, altering coastlines and winning material for landfill and construction purposes. As a single dredge may be required to maintain a throughput of 7000 tonnes of slurry per hour or more, very large centrifugal pumps are used. Figures 1-1 and 1-2 show, respectively, an exterior view of this type of pump, and a view of a large dredge-pump impeller (Addie & Helmley, 1989). The manufacture of fertiliser is another process involving massive slur- transport operations. Li Florida, phosphate matrix is recovered by huge draglines in open-pit mining operations. It is then slurried, and pumped to the wash plants through pipelines with a typical length of about 10 kilometres. Each year some 34 million tonnes of matrix are transported in this manner. This industry employs centrifugal pumps that are generally smaller than those used in large dredges, but impeller diameters up to 1. 4 m are common, and drive capacity is often in excess of 1000 kW. The transport distance is typically longer than for dredging applications, and Chapter 1 Figure LI. Testing a dredge pump at the GIW Hydraulic Laboratory Figure 1. 2. Impeller for large dredge pump 1. Introduction 3 hence a series of pumping stations is often used. Figure 1-3 shows a boost- pump installation in a phosphate pipeline.

1,1 Applications of Slurry Transport Vast tonnages are pumped every year in the form of solid-liquid mixtures, known as slurries. The application which involves the largest quantities is the dredging industry, continually maintaining navigation in harbours and rivers, altering coastlines and winning material for landfill and construction purposes. As a single dredge may be required to maintain a throughput of 7000 tonnes of slurry per hour or more, very large centrifugal pumps are used. Figures 1-1 and 1-2 show, respectively, an exterior view of this type of pump, and a view of a large dredge-pump impeller (Addie & Helmley, 1989). The manufacture of fertiliser is another process involving massive slur- transport operations. Li Florida, phosphate matrix is recovered by huge draglines in open-pit mining operations. It is then slurried, and pumped to the wash plants through pipelines with a typical length of about 10 kilometres. Each year some 34 million tonnes of matrix are transported in this manner. This industry employs centrifugal pumps that are generally smaller than those used in large dredges, but impeller diameters up to 1. 4 m are common, and drive capacity is often in excess of 1000 kW. The transport distance is typically longer than for dredging applications, and Chapter 1 Figure LI. Testing a dredge pump at the GIW Hydraulic Laboratory Figure 1. 2. Impeller for large dredge pump 1. Introduction 3 hence a series of pumping stations is often used. Figure 1-3 shows a boost- pump installation in a phosphate pipeline.

In recent years, interest in the technology of gas cleaning at high temperatures has grown, driven in part by environmental legislation but also by demands for increases in process efficiency and intensity - notably for power generation and waste incineration. Some techniques for high temperature gas cleaning have now reached practical exploitation, and industrial applications are described by some of the contributors to this volume. This book should be of interest to all in the process industries and in the associated research community who are concerned with collecting particulates and gaseous components at temperatures above 200 degrees centigrade. Many of the major industrial trials of hot gas cleaning techniques since 1986, in both North America and Europe, are included. In particular, authors from both academic and industrial sectors consider: developments in processes and devices to remove particles from hot gas streams; measurement and analysis of particulate and gaseous components; combined processes for the removal of vapours and acid gases using "dry scrubbing" and related techniques; and applications in the process industries and in advanced power generation.This book should be of interest to chemical and process engineers in the industrial and academic sectors.

Over half of the products of the chemical and process industries are sold in a particulate form. The range of such products is vast: from agrochemicals to pigments, from detergents to foods, from plastics to pharmaceuticals. However, surveys of the performance of processes designed to produce particulate products have consistently shown inadequate design and poor reliability. `Particle technology' is a new subject facing new challenges. Chemical and process engineering is becoming less concerned with the design of plants to produce generic simple chemicals (which are often single phase fluids) and is now more concerned with speciality `effect' chemicals which may often be in particulate form. Chemical and process engineers are also being recruited in increasing numbers into areas outside their tranditional fields, such as the food industry, pharmaceuticals and the manufacture of a wide variety of consumer products. This book has been written to meet their needs. It provides comprehensive coverage of the technology of particulate solids, in a form which is both accessible and concise enough to be useful to engineering and science students in the final year of an undergraduate degree, and at Master's level. Although it was written with students of chemical engineering in mind, it will also be of use and interest to students of other disciplines. It comprises an account of the fundamentals of teh subject, illustrated by worked examples, and followed by a wide range of selected applications.

The aim of this book is to link demand and supply of environmental information in the field of Life Cycle Management. The book is based on the results of the CHAINET concerted action financed by EU-DGXII for the work period 1998-2000, and is intended to build bridges between the different scientific communities in the field of Life Cycle Management. A structured approach is followed, meaning that both demand and supply of environmental information are characterised, after which the two are linked.

Over half of the products of the chemical and process industries are sold in a particulate form. The range of such products is vast: from agrochemicals to pigments, from detergents to foods, from plastics to pharmaceuticals. However, surveys of the performance of processes designed to produce particulate products have consistently shown inadequate design and poor reliability. `Particle technology'' is a new subject facing new challenges. Chemical and process engineering is becoming less concerned with the design of plants to produce generic simple chemicals (which are often single phase fluids) and is now more concerned with speciality `effect'' chemicals which may often be in particulate form. Chemical and process engineers are also being recruited in increasing numbers into areas outside their tranditional fields, such as the food industry, pharmaceuticals and the manufacture of a wide variety of consumer products. This book has been written to meet their needs. It provides comprehensive coverage of the technology of particulate solids, in a form which is both accessible and concise enough to be useful to engineering and science students in the final year of an undergraduate degree, and at Master''s level. Although it was written with students of chemical engineering in mind, it will also be of use and interest to students of other disciplines. It comprises an account of the fundamentals of teh subject, illustrated by worked examples, and followed by a wide range of selected applications.

The aim of this book is to link demand and supply of environmental information in the field of Life Cycle Management. The book is based on the results of the CHAINET concerted action financed by EU-DGXII for the work period 1998-2000, and is intended to build bridges between the different scientific communities in the field of Life Cycle Management. A structured approach is followed, meaning that both demand and supply of environmental information are characterised, after which the two are linked.

The aim of this book is to link demand and supply of environmental information in the field of Life Cycle Management. The book is based on the results of the CHAINET concerted action financed by EU-DGXII for the work period 1998-2000, and is intended to build bridges between the different scientific communities in the field of Life Cycle Management. A structured approach is followed, meaning that both demand and supply of environmental information are characterised, after which the two are linked.

This volume comprises the papers presented at the Second International Symposium on Gas Cleaning at High Temperatures, held at the University of Surrey, Guildford, UK on 27-29 September, 1993. The Symposium was organised by the Department of Chemical and Process Engineering and the Centre for Environmental Strategy of the University of Surrey, and co-sponsored by The Institution of Chemical Engineers, The Filtration Society and the Royal Society of Chemistry. Co-chairmen R. Clift Centre for Environmental Strategy, University of Surrey J. P. K. Seville Department of Chemical and Process Engineering, University of Surrey Secretary Centre for Environmental Strategy, University of Surrey J. Libaert Scientific Committee British Coal Research Establishment, Cheltenham, UK P. Cahill Shell International, The Hague, Netherlands W. A. Dries University of Karlsruhe, Germany P. Gang Van Tongeren International, Godalming, UK R. R. Greenfield Blue Circle Technical Centre, Greenhithe, UK C. P. Kerton Powergen, Solihull, UK W. S. Kyte Separation Processes Service, Harwell, UK K. Morris Pall Process Filtration, Portsmouth, UK N. Moss Pilkington, Ormskirk, UK G. A.Rimmer Lodge Sturtevant, Birmingham, UK A. Russell-Jones J. Strickland Davy McKee, Stockton-an-Tees, UK Glosfume Environmental Controls, Ashleworth, UK C. J. Withers Financial sponsors Shell International Inc.

Over half of the products of the chemical and process industries are sold in a particulate form. The range of such products is vast: from agrochemicals to pigments, from detergents to foods, from plastics to pharmaceuticals. However, surveys of the performance of processes designed to produce particulate products have consistently shown inadequate design and poor reliability. `Particle technology' is a new subject facing new challenges. Chemical and process engineering is becoming less concerned with the design of plants to produce generic simple chemicals (which are often single phase fluids) and is now more concerned with speciality `effect' chemicals which may often be in particulate form. Chemical and process engineers are also being recruited in increasing numbers into areas outside their tranditional fields, such as the food industry, pharmaceuticals and the manufacture of a wide variety of consumer products. This book has been written to meet their needs. It provides comprehensive coverage of the technology of particulate solids, in a form which is both accessible and concise enough to be useful to engineering and science students in the final year of an undergraduate degree, and at Master's level. Although it was written with students of chemical engineering in mind, it will also be of use and interest to students of other disciplines. It comprises an account of the fundamentals of teh subject, illustrated by worked examples, and followed by a wide range of selected applications.