The Minerals, Metals & Materials Society (TMS) is a member-driven international professional society dedicated to fostering the exchange of learning and ideas across the entire range of materials science and engineering, from minerals processing and primary metals production, to basic research and the advanced applications of materials. Included among its nearly 13,000 professional and student members are metallurgical and materials engineers, scientists, researchers, educators, and administrators from more than 70 countries on six continents.

• Part 1: Energy and Environmental Issues in Materials Manufacturing and Processing: Opportunities in the Steel Industry.- Waste Energy Recovery Technology of Iron and Steel Industry in China.- Green Manufacturing Process of Shougang Jingtang Steel Plant.- The Introduction and Process Optimization Research of Oxygen Blast Furnace Ironmaking Technology.- Prediction and optimal scheduling of byproduct gases in steel mill: Trends and challenges.- Processing Non-Oriented Electrical Steels Using Inclined/Skew Rolling Schemes.- A Possible Way for Efficient Utilization of Coal Energy: The Combined Process of Ironmaking with Gasoline Synthesis and Electricity Generation.- The influence of water vapour on the fuming rate in a ferromanganese system.- Part 2: Energy and Environmental Issues in Materials Manufacturing and Processing: Opportunities in Aluminum Production, Waste Heat and Water Recovery.- Approach for pyrolysis gas release modelling and its potential for enhanced energy efficiency of aluminium remelting furnaces.- Numerical approach for the implementation of the interaction of pyrolysis gases and combustion products in an aluminium melting furnace.- Fluoropolymer Coated Condensing Heat Exchangers for Low-grade Waste Heat Recovery.- Nitrate and other anion removal from waste water using the Hydroflex technology.- Mechanical Analysis of Raceway Formation in Bulk Bed of Blast Furnace.- Part 3: Materials for Coal-Based Power: Materials For Coal-Based Power: Session I.- Ni-Fe based alloy GH984G used for 700 coal-fired power plant.- Part 4: Materials for Coal-Based Power: Materials For Coal-Based Power: Session II.- Creep strength and oxidation resistance of industrially made G115 Steel pipe.- Accelerated creep test for new steels and welds.- Part 5: Materials for Coal-Based Power: Materials For Coal-Based Power: Session IV.- The Reliability Analysis of 12Cr1MoVG and T23 Used for USC Boilers Water Wall.- Part 6: Materials for Coal-Based Power: Poster Session.- Effect ofhigh-frequency induction hardening on stress corrosion of a 12% Cr martensitic stainless steel.- Fireside corrosion behaviors of Inconel 740 H superalloy in various SO2 contents.- High Cycle Fatigue Behavior of HAYNES282 Superalloy.- Recent Development in the Characteristics of Alloy 625 for A-USC Steam Turbine Castings.- Part 7: Materials for Gas Turbines: Coatings.- EVOLUTION OF THE THERMAL CONDUCTIVITY OF Sm2Zr2O7 UNDER CMAS ATTACK.- Part 8: Materials for Gas Turbines: Hot Corrosion and New Materials.- Development of a new high strength and hot corrosion resistant directionally solidified superalloy DZ409.- Part 9: Materials for Gas Turbines: Microstructure and Processing.- Modeling the Diffusion of Minor Elements in Different MCrAlY – Superalloy Substrates at High Temperature.- ON HEALING MECHANISM OF CAST POROSITIES IN CAST NI-BASED SUPERALLOY BY HOT ISOSTATIC PRESSING.- The Influence of Dendritic Segregation Degree to the Recrystallization Nucleation in U4720LI.- Part 10: Materials for Gas Turbines: Poster Session.- Stress Rupture Properties of Alloy 783.- Study on the Undercoolability and Single Crystal Castability of Nickel-Based Superalloys.- Part 11: Materials for Nuclear Energy: Materials for Nuclear Applications I.- Enhancing the High-Cycle Fatigue Property of 316 Austenitic Stainless Steels through Introduction of Mechanical Twins by Cold-Drawing.- Part 12: Materials for Nuclear Energy: Materials for Nuclear Applications II.- Microstructure Evolution of a Reactor Pressure Vessel Steel during High-temperature Tempering.-  Part 13: Materials for Nuclear Energy: Environmental Effects.- Effect of Steam Pressure on the Oxidation Behaviour of Alloy 625.- Friction Stir Processing of Degraded Austenitic Stainless Steel Nuclear Fuel Dry Cask Storage System Canisters.- Part 14: Materials for Nuclear Energy: Accident Tolerant Fuels & Irradiation Effects.- The Mechanical Response of Advanced Claddings during Proposed Reactivity Initiated Accident Conditions.-First principles investigations of alternative nuclear fuels.- Comparative study of thermal conductivity of SiC and BeO from ab initio calculations.- Part 15: Materials for Oil and Gas and AMREE Oil & Gas III.- Anisotropic behaviors for X100 high grade pipeline steel under stress constraints.- Co-relation of microstructural features with tensile and toughness characteristics of X70 grade steel.- Development and applications of new generation Ni-containing cryogenic steels in China.- Microstructure analysis and weldability investigation of stainless steel clad plate.- Microstructure and Properties of High Performance Pipeline Steels.- Sensitivity variation of nanomaterials at different operating temperature conditions.

The Minerals, Metals & Materials Society (TMS) is a member-driven international professional society dedicated to fostering the exchange of learning and ideas across the entire range of materials science and engineering, from minerals processing and primary metals production, to basic research and the advanced applications of materials. Included among its nearly 13,000 professional and student members are metallurgical and materials engineers, scientists, researchers, educators, and administrators from more than 70 countries on six continents.

• Part 1: Energy and Environmental Issues in Materials Manufacturing and Processing: Opportunities in the Steel Industry.- Waste Energy Recovery Technology of Iron and Steel Industry in China.- Green Manufacturing Process of Shougang Jingtang Steel Plant.- The Introduction and Process Optimization Research of Oxygen Blast Furnace Ironmaking Technology.- Prediction and optimal scheduling of byproduct gases in steel mill: Trends and challenges.- Processing Non-Oriented Electrical Steels Using Inclined/Skew Rolling Schemes.- A Possible Way for Efficient Utilization of Coal Energy: The Combined Process of Ironmaking with Gasoline Synthesis and Electricity Generation.- The influence of water vapour on the fuming rate in a ferromanganese system.- Part 2: Energy and Environmental Issues in Materials Manufacturing and Processing: Opportunities in Aluminum Production, Waste Heat and Water Recovery.- Approach for pyrolysis gas release modelling and its potential for enhanced energy efficiency of aluminium remelting furnaces.- Numerical approach for the implementation of the interaction of pyrolysis gases and combustion products in an aluminium melting furnace.- Fluoropolymer Coated Condensing Heat Exchangers for Low-grade Waste Heat Recovery.- Nitrate and other anion removal from waste water using the Hydroflex technology.- Mechanical Analysis of Raceway Formation in Bulk Bed of Blast Furnace.- Part 3: Materials for Coal-Based Power: Materials For Coal-Based Power: Session I.- Ni-Fe based alloy GH984G used for 700 coal-fired power plant.- Part 4: Materials for Coal-Based Power: Materials For Coal-Based Power: Session II.- Creep strength and oxidation resistance of industrially made G115 Steel pipe.- Accelerated creep test for new steels and welds.- Part 5: Materials for Coal-Based Power: Materials For Coal-Based Power: Session IV.- The Reliability Analysis of 12Cr1MoVG and T23 Used for USC Boilers Water Wall.- Part 6: Materials for Coal-Based Power: Poster Session.- Effect ofhigh-frequency induction hardening on stress corrosion of a 12% Cr martensitic stainless steel.- Fireside corrosion behaviors of Inconel 740 H superalloy in various SO2 contents.- High Cycle Fatigue Behavior of HAYNES282 Superalloy.- Recent Development in the Characteristics of Alloy 625 for A-USC Steam Turbine Castings.- Part 7: Materials for Gas Turbines: Coatings.- EVOLUTION OF THE THERMAL CONDUCTIVITY OF Sm2Zr2O7 UNDER CMAS ATTACK.- Part 8: Materials for Gas Turbines: Hot Corrosion and New Materials.- Development of a new high strength and hot corrosion resistant directionally solidified superalloy DZ409.- Part 9: Materials for Gas Turbines: Microstructure and Processing.- Modeling the Diffusion of Minor Elements in Different MCrAlY – Superalloy Substrates at High Temperature.- ON HEALING MECHANISM OF CAST POROSITIES IN CAST NI-BASED SUPERALLOY BY HOT ISOSTATIC PRESSING.- The Influence of Dendritic Segregation Degree to the Recrystallization Nucleation in U4720LI.- Part 10: Materials for Gas Turbines: Poster Session.- Stress Rupture Properties of Alloy 783.- Study on the Undercoolability and Single Crystal Castability of Nickel-Based Superalloys.- Part 11: Materials for Nuclear Energy: Materials for Nuclear Applications I.- Enhancing the High-Cycle Fatigue Property of 316 Austenitic Stainless Steels through Introduction of Mechanical Twins by Cold-Drawing.- Part 12: Materials for Nuclear Energy: Materials for Nuclear Applications II.- Microstructure Evolution of a Reactor Pressure Vessel Steel during High-temperature Tempering.-  Part 13: Materials for Nuclear Energy: Environmental Effects.- Effect of Steam Pressure on the Oxidation Behaviour of Alloy 625.- Friction Stir Processing of Degraded Austenitic Stainless Steel Nuclear Fuel Dry Cask Storage System Canisters.- Part 14: Materials for Nuclear Energy: Accident Tolerant Fuels & Irradiation Effects.- The Mechanical Response of Advanced Claddings during Proposed Reactivity Initiated Accident Conditions.-First principles investigations of alternative nuclear fuels.- Comparative study of thermal conductivity of SiC and BeO from ab initio calculations.- Part 15: Materials for Oil and Gas and AMREE Oil & Gas III.- Anisotropic behaviors for X100 high grade pipeline steel under stress constraints.- Co-relation of microstructural features with tensile and toughness characteristics of X70 grade steel.- Development and applications of new generation Ni-containing cryogenic steels in China.- Microstructure analysis and weldability investigation of stainless steel clad plate.- Microstructure and Properties of High Performance Pipeline Steels.- Sensitivity variation of nanomaterials at different operating temperature conditions.

The Minerals, Metals & Materials Society (TMS) is a member-driven international professional society dedicated to fostering the exchange of learning and ideas across the entire range of materials science and engineering, from minerals processing and primary metals production, to basic research and the advanced applications of materials. Included among its nearly 13,000 professional and student members are metallurgical and materials engineers, scientists, researchers, educators, and administrators from more than 70 countries on six continents.

• Part 1: Energy and Environmental Issues in Materials Manufacturing and Processing: Opportunities in the Steel Industry.- Waste Energy Recovery Technology of Iron and Steel Industry in China.- Green Manufacturing Process of Shougang Jingtang Steel Plant.- The Introduction and Process Optimization Research of Oxygen Blast Furnace Ironmaking Technology.- Prediction and optimal scheduling of byproduct gases in steel mill: Trends and challenges.- Processing Non-Oriented Electrical Steels Using Inclined/Skew Rolling Schemes.- A Possible Way for Efficient Utilization of Coal Energy: The Combined Process of Ironmaking with Gasoline Synthesis and Electricity Generation.- The influence of water vapour on the fuming rate in a ferromanganese system.- Part 2: Energy and Environmental Issues in Materials Manufacturing and Processing: Opportunities in Aluminum Production, Waste Heat and Water Recovery.- Approach for pyrolysis gas release modelling and its potential for enhanced energy efficiency of aluminium remelting furnaces.- Numerical approach for the implementation of the interaction of pyrolysis gases and combustion products in an aluminium melting furnace.- Fluoropolymer Coated Condensing Heat Exchangers for Low-grade Waste Heat Recovery.- Nitrate and other anion removal from waste water using the Hydroflex technology.- Mechanical Analysis of Raceway Formation in Bulk Bed of Blast Furnace.- Part 3: Materials for Coal-Based Power: Materials For Coal-Based Power: Session I.- Ni-Fe based alloy GH984G used for 700 coal-fired power plant.- Part 4: Materials for Coal-Based Power: Materials For Coal-Based Power: Session II.- Creep strength and oxidation resistance of industrially made G115 Steel pipe.- Accelerated creep test for new steels and welds.- Part 5: Materials for Coal-Based Power: Materials For Coal-Based Power: Session IV.- The Reliability Analysis of 12Cr1MoVG and T23 Used for USC Boilers Water Wall.- Part 6: Materials for Coal-Based Power: Poster Session.- Effect ofhigh-frequency induction hardening on stress corrosion of a 12% Cr martensitic stainless steel.- Fireside corrosion behaviors of Inconel 740 H superalloy in various SO2 contents.- High Cycle Fatigue Behavior of HAYNES282 Superalloy.- Recent Development in the Characteristics of Alloy 625 for A-USC Steam Turbine Castings.- Part 7: Materials for Gas Turbines: Coatings.- EVOLUTION OF THE THERMAL CONDUCTIVITY OF Sm2Zr2O7 UNDER CMAS ATTACK.- Part 8: Materials for Gas Turbines: Hot Corrosion and New Materials.- Development of a new high strength and hot corrosion resistant directionally solidified superalloy DZ409.- Part 9: Materials for Gas Turbines: Microstructure and Processing.- Modeling the Diffusion of Minor Elements in Different MCrAlY – Superalloy Substrates at High Temperature.- ON HEALING MECHANISM OF CAST POROSITIES IN CAST NI-BASED SUPERALLOY BY HOT ISOSTATIC PRESSING.- The Influence of Dendritic Segregation Degree to the Recrystallization Nucleation in U4720LI.- Part 10: Materials for Gas Turbines: Poster Session.- Stress Rupture Properties of Alloy 783.- Study on the Undercoolability and Single Crystal Castability of Nickel-Based Superalloys.- Part 11: Materials for Nuclear Energy: Materials for Nuclear Applications I.- Enhancing the High-Cycle Fatigue Property of 316 Austenitic Stainless Steels through Introduction of Mechanical Twins by Cold-Drawing.- Part 12: Materials for Nuclear Energy: Materials for Nuclear Applications II.- Microstructure Evolution of a Reactor Pressure Vessel Steel during High-temperature Tempering.-  Part 13: Materials for Nuclear Energy: Environmental Effects.- Effect of Steam Pressure on the Oxidation Behaviour of Alloy 625.- Friction Stir Processing of Degraded Austenitic Stainless Steel Nuclear Fuel Dry Cask Storage System Canisters.- Part 14: Materials for Nuclear Energy: Accident Tolerant Fuels & Irradiation Effects.- The Mechanical Response of Advanced Claddings during Proposed Reactivity Initiated Accident Conditions.-First principles investigations of alternative nuclear fuels.- Comparative study of thermal conductivity of SiC and BeO from ab initio calculations.- Part 15: Materials for Oil and Gas and AMREE Oil & Gas III.- Anisotropic behaviors for X100 high grade pipeline steel under stress constraints.- Co-relation of microstructural features with tensile and toughness characteristics of X70 grade steel.- Development and applications of new generation Ni-containing cryogenic steels in China.- Microstructure analysis and weldability investigation of stainless steel clad plate.- Microstructure and Properties of High Performance Pipeline Steels.- Sensitivity variation of nanomaterials at different operating temperature conditions.